このセミナーでは、正しい测量を行なうために不重要性な、几乎的な测量の考え方についてまとめました。計測機器を適切に維持安全管理するためには、正しい测量の体谅が不重要性となります。 ■ 対象者

• 初めて計測機器の校正管理に携わる方
• 計測機器の正しい校正方法を学びたい方

■ 所要時間　35分

テクトロニクス最新型２シリーズ・オシロスコープを使った初心者向けのオシロスコープ入門セミナです。
オシロスコープ使用にあたって覚えておくべき基本項目について説明します。
プローブ補正、トリガ設定、自動測定など、前編／後編で解説します。
間違った操作の防ぎ方、オシロスコープの使用における誤解など基本にして必須の知識をご説明します。

オシロスコープ入門 前編 【所要時間：47分】
オシロスコープ入門 後編 【所要時間：54分】

Do you know that Tektronix releases quarterly firmware updates for our beloved 4, 5 and 6 Series Mixed Signal Oscilloscope? We continuously gather your feedbacks and comments as we know that your measurement needs are ever-evolving. The firmware update will make sure that your voice and needs are taken care of.

Join this session and learn what are the latest addition that we have for your oscilloscope:
- New Features
- New Serial Bus Support
- New Applications
- Bug Fixes

Register today!

Measurements and analysis on three-phase power systems are inherently more complex than on single-phase systems. Although oscilloscopes can capture voltage and current waveforms with high sample rates, further calculations are required to produce key power measurements from the data. Learn how Inverter Motor and Drive Analysis (IMDA) software from Tektronix makes it easier than ever to perform three-phase analysis and correlation of control timing and power output characteristics on devices such as AC induction motors, permanent magnet synchronous motors (PMSM), and brushless DC (BLDC) motors. Sign up to watch on demand.

Learn more about the snapback phenomenon and Keithley's solution to tackle this challenging topic in semiconductor test and measurement.

４回にわたってソースメータ(SMU)による試験効率化の方法を徹底解説ソースメータ（SMU）とは？
車載Ethernet 電源やマルチメータと何が違う？皆様からよく頂くご質問にお答えし、SMUの基礎から測定実例や応用アプリケーションなどを交えた入門セミナがオンデマンドでご視聴いただけます。 より深くご理解頂くために、４回にわたって、仕組みから様々な測定事例までSMUによる試験効率化の方法を徹底解説しています。ぜひご視聴ください。

• 実機デモで比較解説 ー SMUのDC電源／電子負荷性能について
• SMUの仕組みとよく使われる機能のご紹介
• SMUを使った代表的な測定事例のご紹介
• ソフトウェアを使ったSMUの自動計測事例

Learn the common challenges for serial bus designers and how to overcome them using capabilities found in the mixed domain oscilloscope.

PCI Express I/O bandwidth has doubled every 3 years on average thereby leading to an increased demand for this full duplex high speed bus architecture. As the industry begins deploying the 5.0 revision with a bit rate of 32 GT/s, new trends and guidelines emerge for receiver compliance and validation.

This webinar will provide an overview of the methods for solving some of the new test and measurement receiver challenges for PCIE® 5.0 at 32.0 GT/s. The key topics covered in this presentation are as follows:
- Status of 5.0 specifications including Base, CEM, and the test specifications
- PCI-SIG® 5.0 compliance program
- Challenges and latest guidelines on 32 GT/s receiver testing from industry experts
    * Nuances of the 32 GT/s stressed eye calibration
    * Handling high loss backchannels with equalization
    * Thoughts on Rx testing with and without spread spectrum clocking (SSC)
- Solving validation challenges with a receiver solution from Anritsu & Tektronix
- PCI Express, PCIE, and PCI-SIG are registered trademarks and/or service marks of PCI-SIG. Register to watch the on-demand webinar today!

Are the bit errors in your data caused by the power supply or sources inside the digital channel? Let's end the dispute by examining the connection between jitter and power integrity. We'll highlight sources of noise likely to cause jitter on serial data lines and look at other power analysis methods from 3-phase inverter analysis to isolated probing.

In this on-demand webinar, will learn how to:
- Detect ripple and its effects on a high-speed serial clock using power rail analysis software
- Mitigate signal integrity problems caused by the PDN (power distribution network)
- See how additional capabilities of modern oscilloscopes make complex power measurements easier and more repeatable